Harbor Freight Tools Greenhouse Kit 94241 User Manual

HOT HOUSE  
MINI GREENHOUSE  
94241  
ASSEMBLY & OPERATING INSTRUCTIONS  
Use only with GFCI electrical outlet  
Due to continuing improvement, actual product may differ slightly from product described herein.  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or  
any artwork contained herein may be reproduced in any shape or form without the  
express written consent of Harbor Freight Tools.  
For technical questions and replacement parts please call 1-800-444-3353.  
 
5.  
6.  
Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and  
refrigerators. There is an increased risk of electric shock if your body is grounded.  
Do not abuse the Power Cord. Never use the Power Cord to carry the Hot House or  
pull the Plug from an outlet. Keep the Power Cord away from heat, oil, and sharp  
edges. Replace damaged Power Cords immediately. Damaged Power Cords increase  
the risk of electric shock.  
7.  
8.  
When operating a power tool outside, use an outdoor extension cord markedW-A”  
or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric  
shock.  
PERSONAL SAFETY  
Stay alert. Watch what you are doing, and use common sense when operating the  
Hot House. Do not operate the Hot House while tired or under the influence of drugs,  
alcohol, or medication.  
9.  
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.  
10.  
Use safety equipment. Always wear eye protection during assembly and  
maintenance.  
11.  
WARNING! People with pacemakers should consult their physician(s) before using  
this product. Operation of electrical equipment in close proximity to a heart pace  
maker could cause interference or failure of the pacemaker.  
TOOL USE AND CARE  
12.  
13.  
Do not overload the Hot House. Use the correct Hot House for your application.  
Disconnect the Power Cord Plug from the power source before inserting seeds,  
making any adjustments, watering, or storing the Hot House. Such  
preventive safety measures reduce the risk of turning on the product accidentally.  
14.  
15.  
Store idle products out of reach of children and other untrained persons.  
Maintain the Hot House with care. Do not use a damaged Hot House. Tag damaged  
Hot House “Do not use” until repaired.  
SERVICE  
16.  
17.  
When servicing the Hot House, use only identical replacement parts. Use of  
unauthorized parts or failure to follow maintenance instructions may create a risk of electric  
shock or injury.  
Always unplug the Hot House from its electrical outlet before performing any  
watering, inspection maintenance, planting or cleaning procedures.  
SKU 94241  
For technical questions please call 1-800-444-3353.  
Page 3  
 
GROUNDING  
WARNING!  
Improperly connecting the grounding wire can result in the risk of electric shock. Check with  
a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not  
modify the power cord plug provided with the Hot House. Never remove the grounding prong  
from the plug. Do not use the Hot House if the power cord or plug is damaged. If damaged,  
have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper  
outlet installed by a qualified electrician.  
Warning: Only use this Hot House with a GFCI electrical outlet.  
To comply with the National Electrical Code (NFPA70), and to provide additional protection  
from the risk of electric shock, this Hot House/Mini Greenhouse should only be connected to  
a receptacle that is protected by a ground fault circuit interrupter (GFCI).  
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS  
1.  
2.  
3.  
Tools marked with “Grounding Required” have a three wire cord and three prong grounding  
plug. The plug must be connected to a properly grounded outlet. If the Hot House  
should electrically malfunction or break down, grounding provides a low resistance path to  
carry electricity away from the user, reducing the risk of electric shock. (See Figure A.  
The grounding prong in the plug is connected through the green wire inside the cord to the  
grounding system in the tool. The green wire in the cord must be the only wire connected to  
the Hot House’s grounding system and must never be attached to an electrically “live”  
terminal. (See Figure A.)  
A grounded appliance must be plugged into an appropriate outlet, properly installed and  
grounded in accordance with all codes and ordinances. The plug and outlet should look like  
those in the following illustration. (See Figure A.)  
Figure A  
DOUBLE INSULATED APPLIANCES: APPLIANCES WITH TWO PRONG PLUGS  
Note: The Hot House has a Two Prong Plug.  
1.  
Appliances marked “Double Insulated” do not require grounding. They have a special double  
insulation system which satisfies OSHA requirements and complies with the applicable  
standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the  
National Electrical Code. (See Figure B.)  
SKU 94241  
For technical questions please call 1-800-444-3353.  
Page 4  
 
2.  
Double insulated tools may be used in either of the 120 volt outlets shown in the following  
illustration. (See Figure B.)  
Figure B  
EXTENSION CORDS  
1.  
2.  
Grounded appliances require a three wire extension cord. Double Insulated products can  
use either a two or three wire extension cord.  
As the distance from the supply outlet increases, you must use a heavier gauge extension  
cord. Using extension cords with inadequately sized wire causes a serious drop in voltage,  
resulting in loss of power and possible tool damage. (See Figure C, next page.)  
3.  
4.  
5.  
The smaller the gauge number of the wire, the greater the capacity of the cord. For  
example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.)  
When using more than one extension cord to make up the total length, make sure each cord  
contains at least the minimum wire size required. (See Figure C.)  
If you are using one extension cord for more than one tool, add the nameplate amperes and  
use the sum to determine the required minimum cord size. (See Figure C.)  
6.  
7.  
If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A”  
(“W” in Canada) to indicate it is acceptable for outdoor use.  
Make sure your extension cord is properly wired and in good electrical condition. Always  
replace a damaged extension cord or have it repaired by a qualified electrician before using  
it.  
8.  
Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.  
Figure C  
SKU 94241  
For technical questions please call 1-800-444-3353.  
Page 5  
 
Specific Safety Rules for the Hot House  
1.  
2.  
Maintain labels and nameplates on the Hot House. These carry important information. If  
the labels are unreadable or missing, contact Harbor Freight Tools for replacement.  
Always place the Hot House on a dry, flat, level, sturdy non-flammable work surface  
capable of supporting the weight of the Hot House and any plants or seeds. Make  
sure to place the Hot House in a location that is out of reach of children.  
3.  
Turn off the Hot House and unplug it from its electrical outlet before doing any  
planting or maintenance.  
WARNING: The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be  
understood by the operator that common sense and caution are factors which  
cannot be built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking your Hot House, check to make sure that it is intact and undamaged. If it is  
damaged or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.  
Assembly-Using the Hot House to Germinate Seeds  
Your Hot House comes completely assembled. You will have to supply seedlings (not included) and  
set up the Mat, Tray, Seeding Container and Dome yourself. The Hot House must be unplugged  
before adding any seeds or doing any work with it. It is important that you read the entire manual to  
become familiar with the product BEFORE you operate the Hot House.  
1.  
2.  
Place the Seeding Insert (2) into the Black Tray (3).  
Decide on seeds and a growing medium such as garden soil or a soiless growing mix (all  
not included). Information on the ideal mix to use can be obtained online or through your  
local library.  
3.  
4.  
With the Seeding Insert separated from the Black Tray (3) and Mat (4), fill each section of  
the Seeding Insert (2) with growing mix.  
Place the seeds individually into each section of the Seeding Insert (2). The seeds should  
be placed into the growing mix according to the instructions provided on the packet along  
with the seeds. Seeds can generally be covered to about three times the depth of the seed.  
5.  
6.  
Moisten the growing mix.  
Most seedlings germinate best if the soil temperature is around 75 degrees F. If soil is too  
cold the seeds may not germinate. Seeds are done germinating once they sprout.  
7.  
8.  
Placet the Transparent Dome (1) onto the Black Tray (3). Set the assembled contents (Black  
Tray (3), Seeding Insert (2) and Transparent Dome (1) onto the Heating Mat (4).  
Plug the Heating Mat (4) into a 120V GFCI outlet.  
SKU 94241  
For technical questions please call 1-800-444-3353.  
Page 6  
 
9.  
Replant the seeds. Once the seeds are replanted, the Hot House may be used to  
begin a new batch of seeds.  
10.  
When watering your seeds, make certain to not overflow the seed containers or spill  
excessive water on the Heating Mat (4).  
Storage and Maintenance  
1.  
Store the Hot House in a place out of the sunlight. Because parts of the Hot House are  
easily damaged by impact or being dropped, store in a safe and secure location out of the  
reach of children.  
2.  
3.  
Clean and wash out the Seeding Insert (2) and Black Tray (3) after each use. Make certain  
that all components are free of dirt, debris, fungus and mold.  
Before each use, inspect the Hot House and make certain that no parts are cracked or  
damaged. Make certain Mat is intact and wiring is not damaged or broken.  
Note: Some parts are listed and shown for illustration purposes only and are not available  
individually as replacement parts.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE  
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY  
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY  
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED  
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION  
OF REPLACEMENT PARTS THERETO.  
Parts List  
Part #  
Description  
Quantity  
1
2
3
4
Transparent Dome  
Seeding Insert  
Black Tray  
1
1
1
1
Heating Mat  
1
2
3
4
SKU 94241  
For technical questions please call 1-800-444-3353.  
Page 7  
 

Hans Grohe Plumbing Product 41738XX0 User Manual
Harman Kardon DVD Player DVD 21 User Manual
Honeywell Boiler C User Manual
Honeywell Security Camera HD3MDIP User Manual
Honeywell Thermostat CM721 User Manual
Hotpoint Dishwasher BFT68 User Manual
Hotpoint Washer Dryer AQD1170F User Manual
HTC Cell Phone NM8LIBR100 User Manual
IBM Frozen Dessert Maker AIX5L User Manual
IFB Appliances Microwave Oven 22DGSC1 User Manual